Wemos SSD1306 128x64 0.96 not working with Universal Display Driver

[ThomasDesloovere]

PROBLEM DESCRIPTION

I have multiple types of oled display most of them have the SSD1306 driver. Since Tasmota came out with the Universal Display Driver they are a bit more of a pain in the ass to configure. I have a ESP running Tasmota 13.2.0 with SSD1306 display from Wemos/Lolin that is working great, i wanted to replicate the setup with a newer version of Tasmota with the same display (known good) I configured a new esp with Tasmota 14.2.0.6 Here the lolin display doesn't work, if i connect an off brand random display with the SSD1306 driver it works perfecly fine.

REQUESTED INFORMATION

Make sure your have performed every step and checked the applicable boxes before submitting your issue. Thank you!

• Read the Contributing Guide and Policy and the Code of Conduct
• Searched the problem in issues
• Searched the problem in discussions
• Searched the problem in the docs
• Searched the problem in the chat
• Device used (e.g., Sonoff Basic): Lolin / Wemos ESP8266 D1 mini
• Tasmota binary firmware version number used: 14.2.0.6
  • Pre-compiled
  • Self-compiled
• Flashing tools used: ESPWebTool
• Provide the output of command: Backlog Template; Module; GPIO 255:

  Configuration output here:
19:59:42.583 RSL: RESULT = {"NAME":"Generic","GPIO":[1,1,1,1,1,1,1,1,1,1,1,1,1,1],"FLAG":0,"BASE":18}
19:59:42.791 RSL: RESULT = {"Module":{"0":"Generic"}}
19:59:43.064 RSL: RESULT = {"GPIO0":{"480":"Buzzer"},"GPIO1":{"0":"None"},"GPIO2":{"1376":"WS2812"},"GPIO3":{"5730":"Option A3"},"GPIO4":{"640":"I2C SDA"},"GPIO5":{"608":"I2C SCL"},"GPIO9":{"0":"None"},"GPIO10":{"0":"None"},"GPIO12":{"32":"Button1"},"GPIO13":{"9248":"LD2410 Tx"},"GPIO14":{"1088":"IRrecv"},"GPIO15":{"9280":"LD2410 Rx"},"GPIO16":{"1056":"IRsend1"},"GPIO17":{"0":"None"}}

• If using rules, provide the output of this command: Backlog Rule1; Rule2; Rule3:

  Rules output here:
20:00:14.286 RSL: RESULT = {"Rule1":{"State":"OFF","Once":"OFF","StopOnError":"OFF","Length":0,"Free":511,"Rules":""}}
20:00:14.495 RSL: RESULT = {"Rule2":{"State":"OFF","Once":"OFF","StopOnError":"OFF","Length":0,"Free":511,"Rules":""}}
20:00:14.697 RSL: RESULT = {"Rule3":{"State":"OFF","Once":"OFF","StopOnError":"OFF","Length":168,"Free":343,"Rules":":H,SSD1306,128,64,1,I2C,3c,*,*,* :S,0,2,1,0,30,20 :I AE D5,80 A8,3F D3,00 40 8D,14 20,00 A1 C8 DA,12 81,9F D9,F1 DB,40 A4 A6 AF :o,AE :O,AF :A,00,10,40,00,00 :i,A6,A7 #"}}

• Provide the output of this command: Status 0:

  STATUS 0 output here:
20:00:34.417 RSL: STATUS = {"Status":{"Module":0,"DeviceName":"Tasmota","FriendlyName":["Tasmota","Tasmota2"],"Topic":"tasmota_3E53A7","ButtonTopic":"0","Power":"11","PowerLock":"00","PowerOnState":3,"LedState":1,"LedMask":"FFFF","SaveData":1,"SaveState":1,"SwitchTopic":"0","SwitchMode":[0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0],"ButtonRetain":0,"SwitchRetain":0,"SensorRetain":0,"PowerRetain":0,"InfoRetain":0,"StateRetain":0,"StatusRetain":0}}
20:00:34.422 RSL: STATUS1 = {"StatusPRM":{"Baudrate":254400,"SerialConfig":"8N1","GroupTopic":"tasmotas","OtaUrl":"http://ota.tasmota.com/tasmota/release/tasmota.bin.gz","RestartReason":"External System","Uptime":"0T00:21:37","StartupUTC":"2024-09-27T17:38:57","Sleep":50,"CfgHolder":4617,"BootCount":18,"BCResetTime":"2024-09-27T14:55:59","SaveCount":61,"SaveAddress":"F9000"}}
20:00:34.428 RSL: STATUS2 = {"StatusFWR":{"Version":"14.2.0.6(tasmota)","BuildDateTime":"2024-09-27T14:00:42","Boot":31,"Core":"2_7_7","SDK":"2.2.2-dev(38a443e)","CpuFrequency":80,"Hardware":"ESP8266EX","CR":"375/699"}}
20:00:34.433 RSL: STATUS3 = {"StatusLOG":{"SerialLog":0,"WebLog":2,"MqttLog":0,"SysLog":0,"LogHost":"","LogPort":514,"SSId":["WiFi-2.4-7538",""],"TelePeriod":300,"Resolution":"558180C0","SetOption":["00008009","2805C80001000600003C5A0A192800000000","00000080","20006000","00004000","00000000"]}}
20:00:34.446 RSL: STATUS4 = {"StatusMEM":{"ProgramSize":892,"Free":108,"Heap":17,"ProgramFlashSize":1024,"FlashSize":4096,"FlashChipId":"16405E","FlashFrequency":40,"FlashMode":"DOUT","Features":["0809","8FBAC787","043682A1","000215CF","010013C0","D000F981","00004024","00001000","54000020","04000480","00000000"],"Drivers":"1,2,!3,4,5,!6,7,!8,9,10,12,13,!16,!18,!19,!20,!21,!22,24,26,!27,29,!30,!35,!37,!45,62,!68","Sensors":"1,2,3,4,5,6,7,9,10,14,63,102,111","I2CDriver":"3,5,7,8,10,11,15,43,47,84"}}
20:00:34.451 RSL: STATUS5 = {"StatusNET":{"Hostname":"tasmota-3E53A7-5031","IPAddress":"192.168.1.17","Gateway":"192.168.1.1","Subnetmask":"255.255.255.0","DNSServer1":"192.168.1.1","DNSServer2":"0.0.0.0","Mac":"B4:E6:2D:3E:53:A7","Webserver":2,"HTTP_API":1,"WifiConfig":4,"WifiPower":17.0}}
20:00:34.454 RSL: STATUS6 = {"StatusMQT":{"MqttHost":"","MqttPort":1883,"MqttClientMask":"DVES_%06X","MqttClient":"DVES_3E53A7","MqttUser":"DVES_USER","MqttCount":0,"MAX_PACKET_SIZE":1200,"KEEPALIVE":30,"SOCKET_TIMEOUT":4}}
20:00:34.460 RSL: STATUS7 = {"StatusTIM":{"UTC":"2024-09-27T18:00:34Z","Local":"2024-09-27T20:00:34","StartDST":"2024-03-31T02:00:00","EndDST":"2024-10-27T03:00:00","Timezone":99,"Sunrise":"07:44","Sunset":"19:36"}}
20:00:34.465 RSL: STATUS10 = {"StatusSNS":{"Time":"2024-09-27T20:00:34","LD2410":{"Distance":[0.0,0.0,0.0],"Energy":[0,0]}}}
20:00:34.471 RSL: STATUS11 = {"StatusSTS":{"Time":"2024-09-27T20:00:34","Uptime":"0T00:21:37","UptimeSec":1297,"Heap":17,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":24,"MqttCount":0,"POWER1":"ON","Dimmer":99,"Color":"FC72EC","HSBColor":"307,55,99","Channel":[99,45,93],"Scheme":0,"Width":1,"Fade":"OFF","Speed":1,"LedTable":"ON","Wifi":{"AP":1,"SSId":"WiFi-2.4-7538","BSSId":"58:90:43:A3:75:3E","Channel":1,"Mode":"11n","RSSI":48,"Signal":-76,"LinkCount":1,"Downtime":"0T00:00:05"}}}

• Set weblog to 4 and then, when you experience your issue, provide the output of the Console log:

  Console output here:

TO REPRODUCE

Connect and configure a Lolin / Wemos 128*64 SSD1306

EXPECTED BEHAVIOUR

A functional display.

SCREENSHOTS

If applicable, add screenshots to help explain your problem.

ADDITIONAL CONTEXT

Add any other context about the problem here.

(Please, remember to close the issue when the problem has been addressed)

[sfromis]

Did you make sure to include universal display support in your build?
#define USE_UNIVERSAL_DISPLAY

And what did you do to include the display descriptor? Without a file system, that could be using the suggestion for doing it in rule set 3. I've seen it work with this:

Rule3 :H,SSD1306,128,64,1,I2C,3c,*,*,* :S,0,2,1,0,30,20 :I AE D5,80 A8,3F D3,00 40 8D,14 20,00 A1 C8 DA,12 81,9F D9,F1 DB,40 A4 A6 AF :o,AE :O,AF :A,00,10,40,00,00 :i,A6,A7 #

You could also make it into a 4M build, to have room for a local file system, a good place to have a display.ini

BTW. You may also need to make sure that the display is powered on, like last toggle in the web UI.

[ThomasDesloovere]

Yes, as stated the version I compiled works on other ssd1306 displays, if connect the wemos display it stays blank. Same i2c address. Yes that is indeed the rule I use. Display toggle was turned on as the other display functions properly.

[sfromis]

Well, if you have verified that Tasmota is doing what it should, it would seem to be up to hardware-level differences, including connections and wiring. "Known good" is not a sufficient indicator of "everything should be ok".

[ThomasDesloovere]

While that is true, there really can’t be any wiring problem. The display connects with a 4 wire cable pre-made that works on the other one, the connector on this esp is also known good as it functions with temperature sensors. If I scan the i2c bus I get the address back from the display. There seems to be a driver difference between 13.2.0 and the universal driver.

[sfromis]

Yes, the universal display driver is a total rewrite of the old concept with separate display drivers per display type. But still, since one display works, and not another, that indicates some hardware-level difference, where details of that would be key to any fix for making it work for both.

[ThomasDesloovere]

Yeah I do understand that.

Lolin display
https://www.wemos.cc/en/latest/d1_mini_shield/oled_0_96.html

Generic display that works
https://www.az-delivery.de/a/s/products/0-96zolldisplay

It's kind of wird because I haven't come across this issue with any other driver. I have used both perfectly fine with Arduino and a SSD1306 library

[sfromis]

Maybe @gemu2015 has some insights or questions?

[gemu2015]

according to the driver source code of your display these init cmds are send
try with this slightly modified descriptor

  :H,SSD1306,128,64,1,I2C,3c,*,*,*
  :S,0,2,1,0,30,20
  :I
  AE
  D5,F0
  A8,3F
  D3,00
  40
  8D,14
  20,00
  A0
  C0
  DA,12
  81,CF
  D9,F1
  DB,40
  A4
  A6
  2E
  AF
  :o,AE
  :O,AF
  :A,00,10,40,00,00
  :i,A6,A7
  #

[ThomasDesloovere]

Hi, thanks for looking in to it. I just tried it, the generic one still functions but the Wemos one still stays black.

[ThomasDesloovere]

Does anyone have any ideas? This is more of an issue than a discussion since it worked in a previous version of Tasmota and now it doesn't anymore. This is kind of annoying since I designed something around this display and it is not fun to redesign the pcb.

[s-hadinger]

Just comment out this line, it's just logging

[ThomasDesloovere]

okay, got it compiled, whats next never done this kind of debugging

[s-hadinger]

Do you have a PC connected to serial? If so just copy the serial output using any terminal software

[ThomasDesloovere]

I got a connection and got the result below.

{ld▒▒|▒l▒| ▒ $▒c|▒▒▒{▒c▒c▒▒'o▒l'o▒▒▒ b8▒lsdsdp▒n▒ ▒l▒▒ #g▒|▒l▒ ▒c▒▒'o▒$▒▒l▒gl or▒ۓocl;▒▒g c$▒rd▒▒<▒ld▒l▒g▒
00:00:00.001 HDW: ESP8266EX
00:00:00.050 CFG: Loaded from flash at FB, Count 33
00:00:00.055 QPC: Count 1
Device : SSD1306
xs : 128
ys : 64
bpp: 1
Addr : 3c
SCL : 5
SDA : 4
SPA : 0
pa_sta: 10
pa_end: 40
SCA : 0
ca_sta: 0
pa_end: ff
WRA : ff
Dsp class init complete
Dsp Init 1 start
I2C cmds: 25
cmd = ae
cmd = d5
cmd = 80
cmd = a8
cmd = 3f
cmd = d3
cmd = 0
cmd = 40
cmd = 8d
cmd = 14
cmd = 20
cmd = 0
cmd = a1
cmd = c8
cmd = da
cmd = 12
cmd = 81
cmd = 9f
cmd = d9
cmd = f1
cmd = db
cmd = 40
cmd = a4
cmd = a6
cmd = af
Dsp Init 1 complete
Dsp Init 2 complete
00:00:00.110 DSP: SSD1306 initialized
00:00:00.116 Project tasmota - Tasmota Version 14.2.0(tasmota)-2_7_7(2024-10-10T08:04:53)
00:00:01.001 WIF: Connecting to AP1 Thomas Boven Channel 6 BSSId AC:8B:A9:34:EA:DA in mode 11n as tasmota-C60FB0-4016...
00:00:02.514 WIF: Connected
00:00:02.768 HTP: Web server active on tasmota-C60FB0-4016 with IP address 192.168.1.10
09:11:55.506 RSL: INFO1 = {"Info1":{"Module":"Thomas","Version":"14.2.0(tasmota)","FallbackTopic":"cmnd/DVES_C60FB0_fb/","GroupTopic":"cmnd/tasmotas/"}}
09:11:55.511 RSL: INFO2 = {"Info2":{"WebServerMode":"Admin","Hostname":"tasmota-C60FB0-4016","IPAddress":"192.168.1.10"}}
09:11:55.521 RSL: INFO3 = {"Info3":{"RestartReason":"External System","BootCount":15}}
09:11:55.529 RSL: RESULT = {"POWER1":"OFF"}
09:11:55.532 RSL: POWER1 = OFF
09:11:55.535 RSL: RESULT = {"POWER2":"ON"}
09:11:55.539 RSL: POWER2 = ON
09:11:57.237 QPC: Reset
09:11:59.254 RSL: STATE = {"Time":"2024-10-10T09:11:59","Uptime":"0T00:00:09","UptimeSec":9,"Heap":22,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":0,"POWER1":"OFF","Dimmer":10,"Color":"1A1A1A","HSBColor":"0,0,10","Channel":[10,10,10],"Scheme":0,"Width":1,"Fade":"OFF","Speed":1,"LedTable":"ON","Wifi":{"AP":1,"SSId":"Thomas Boven","BSSId":"AC:8B:A9:34:EA:DA","Channel":6,"Mode":"11n","RSSI":100,"Signal":-46,"LinkCount":1,"Downtime":"0T00:00:04"}}
`

[s-hadinger]

Everything looks ok, communication via I2C is working. I'm sorry but I'm out of options

[ZioFabry]

@ThomasDesloovere , I don't know if can help... but this is my SSD1306 from Shineworld:
4 wire i2c without RST pin

:H,SSD1306,128,64,1,I2C,3c,*,*,*
:S,0,0,1,0,0,0
:I
FD
12
AE
D5,A0
A8,3F
D3,00
40
A1
C8
DA,12
81,7F
D9,82
DB,34
A4
A6
AF
:o,AE
:O,AF
:A,00,10,40,00,00
:i,A6,A7
#

[ThomasDesloovere]

Hi thanks for your help, as you can read in my other command the problem is now solved.

[ThomasDesloovere]

Hi everyone so I figured it out, thank you for your help. The problem apparently was that the I2C address was wrong. I do remember trying to change it with the command DisplayAddress does not work, you need to change it in the rule. This is kind of a problem because it is not specifically stated in the documentation. Thanks again for the help, I know that it was a stupid problem...

[s-hadinger]

I assumed that you already did i2cscan to check the address, as you mentioned above that they were the same.
The i2c address is in the display ini/rule and does not take into account displayaddress